For Yamaha 704-48205-P1 Top Single Binnacle Console Mount Remote Control Box

Description

Product Features
Fast Idle Mode
​
The fast idle button can be used to advance throttle without shifting into gear. With control lever in Neutral, push on fast idle button(cover) to open throttle for starting and warm-up.
Improved Control Handle
​
With control handle in Neutral and fast idle feature not activated, move control handle to Forward gear or Reverse gear position. Continue movement of control handle in same direction to open (advance) throttle.
Safety Lanyard
​
For Yamaha 704-48205-P1 Top Single Binnacle Console Mount Remote Control Box
Product Features
Fast Idle Mode
​
The fast idle button can be used to advance throttle without shifting into gear. With control lever in Neutral, push on fast idle button(cover) to open throttle for starting and warm-up.
Improved Control Handle
​
With control handle in Neutral and fast idle feature not activated, move control handle to Forward gear or Reverse gear position. Continue movement of control handle in same direction to open (advance) throttle.
Safety Lanyard
​
The cord can secure the operation by being attached to operator's clothing, or arm, or leg. Should operators fall down or leave the helm, the cord will pull out the clip, stopping ignition.
Thumb-Operated Trim/Tilt Switch
​
The power trim and tilt switch is attached to the control lever grip and twin cover. Pushing it UP trims up and tilts up the engine and vice versa.​
For Mercury
​
It fits for Mercury/Mariner OB with integral power trim and 1993 and newer Force OB 40hp.
Pistol Grip Remote Control with Finger Tip Lock Release Installation.
1.Route the trim Switch leads from the control handle assembly through the bezel cover and bezel opening.
2.Allow sufficient in the trim switch leads to permit free movement through the full range of the control handle motion.Do not restrain the trim switch leads with cable ties.
3.Install the remote control module to the bezel .Secure the remote control module with three screws .Tighten the screws to the specified torque.
4.Connect the trim switch connector to the trim motor harness connectors.
5.Install the bushing into the module assembly.Apply a small amount of 2-4 C with Teflon to the inside diameter of the bushing.
6.Align the tabs on the bezel cover with the slots on the bezel .Snap the bezel cover in place.
7.Apply Loctite 271 Threadlocker on the threads of the control handle retaining bolt .
8.Install the control handle assembly onto the remote control module .Ensure the control handle is in neutral and in the desired position.
Package Content:
1 x Remote Control Box with Instruction Manual
Product Features
Fast Idle Mode
​
The fast idle button can be used to advance throttle without shifting into gear. With control lever in Neutral, push on fast idle button(cover) to open throttle for starting and warm-up.
Improved Control Handle
​
With control handle in Neutral and fast idle feature not activated, move control handle to Forward gear or Reverse gear position. Continue movement of control handle in same direction to open (advance) throttle.
Safety Lanyard
​
The cord can secure the operation by being attached to operator's clothing, or arm, or leg. Should operators fall down or leave the helm, the cord will pull out the clip, stopping ignition.
Thumb-Operated Trim/Tilt Switch
​
The power trim and tilt switch is attached to the control lever grip and twin cover. Pushing it UP trims up and tilts up the engine and vice versa.​
For Mercury
​
It fits for Mercury/Mariner OB with integral power trim and 1993 and newer Force OB 40hp.
Pistol Grip Remote Control with Finger Tip Lock Release Installation.
1.Route the trim Switch leads from the control handle assembly through the bezel cover and bezel opening.
2.Allow sufficient in the trim switch leads to permit free movement through the full range of the control handle motion.Do not restrain the trim switch leads with cable ties.
3.Install the remote control module to the bezel .Secure the remote control module with three screws .Tighten the screws to the specified torque.
4.Connect the trim switch connector to the trim motor harness connectors.
5.Install the bushing into the module assembly.Apply a small amount of 2-4 C with Teflon to the inside diameter of the bushing.
6.Align the tabs on the bezel cover with the slots on the bezel .Snap the bezel cover in place.
7.Apply Loctite 271 Threadlocker on the threads of the control handle retaining bolt .
8.Install the control handle assembly onto the remote control module .Ensure the control handle is in neutral and in the desired position.
Package Content:
1 x Remote Control Box with Instruction Manual
Product Features
Fast Idle Mode
​
The fast idle button can be used to advance throttle without shifting into gear. With control lever in Neutral, push on fast idle button(cover) to open throttle for starting and warm-up.
Improved Control Handle
​
With control handle in Neutral and fast idle feature not activated, move control handle to Forward gear or Reverse gear position. Continue movement of control handle in same direction to open (advance) throttle.
Safety Lanyard
​
The cord can secure the operation by being attached to operator's clothing, or arm, or leg. Should operators fall down or leave the helm, the cord will pull out the clip, stopping ignition.
Thumb-Operated Trim/Tilt Switch
​
The power trim and tilt switch is attached to the control lever grip and twin cover. Pushing it UP trims up and tilts up the engine and vice versa.​
For Mercury
​
It fits for Mercury/Mariner OB with integral power trim and 1993 and newer Force OB 40hp.
Pistol Grip Remote Control with Finger Tip Lock Release Installation.
1.Route the trim Switch leads from the control handle assembly through the bezel cover and bezel opening.
2.Allow sufficient in the trim switch leads to permit free movement through the full range of the control handle motion.Do not restrain the trim switch leads with cable ties.
3.Install the remote control module to the bezel .Secure the remote control module with three screws .Tighten the screws to the specified torque.
4.Connect the trim switch connector to the trim motor harness connectors.
5.Install the bushing into the module assembly.Apply a small amount of 2-4 C with Teflon to the inside diameter of the bushing.
6.Align the tabs on the bezel cover with the slots on the bezel .Snap the bezel cover in place.
7.Apply Loctite 271 Threadlocker on the threads of the control handle retaining bolt .
8.Install the control handle assembly onto the remote control module .Ensure the control handle is in neutral and in the desired position.
Package Content:
1 x Remote Control Box with Instruction Manual
Product Features
Fast Idle Mode
​
The fast idle button can be used to advance throttle without shifting into gear. With control lever in Neutral, push on fast idle button(cover) to open throttle for starting and warm-up.
Improved Control Handle
​
With control handle in Neutral and fast idle feature not activated, move control handle to Forward gear or Reverse gear position. Continue movement of control handle in same direction to open (advance) throttle.
Safety Lanyard
​
The cord can secure the operation by being attached to operator's clothing, or arm, or leg. Should operators fall down or leave the helm, the cord will pull out the clip, stopping ignition.
Thumb-Operated Trim/Tilt Switch
​
The power trim and tilt switch is attached to the control lever grip and twin cover. Pushing it UP trims up and tilts up the engine and vice versa.​
For Mercury
​
It fits for Mercury/Mariner OB with integral power trim and 1993 and newer Force OB 40hp.
Pistol Grip Remote Control with Finger Tip Lock Release Installation.
1.Route the trim Switch leads from the control handle assembly through the bezel cover and bezel opening.
2.Allow sufficient in the trim switch leads to permit free movement through the full range of the control handle motion.Do not restrain the trim switch leads with cable ties.
3.Install the remote control module to the bezel .Secure the remote control module with three screws .Tighten the screws to the specified torque.
4.Connect the trim switch connector to the trim motor harness connectors.
5.Install the bushing into the module assembly.Apply a small amount of 2-4 C with Teflon to the inside diameter of the bushing.
6.Align the tabs on the bezel cover with the slots on the bezel .Snap the bezel cover in place.
7.Apply Loctite 271 Threadlocker on the threads of the control handle retaining bolt .
8.Install the control handle assembly onto the remote control module .Ensure the control handle is in neutral and in the desired position.
Package Content:
1 x Remote Control Box with Instruction Manual
Item Specifics
Brand
autopartsclub2018
Manufacturer Part Number
APC1703192018
Warranty
1 Year
Custom Bundle
No
Weight
7lb.
Modified Item
No
Fit for
For Yamaha
Condition
New
Type
Outboard Remote Control
Part Number
704-48205-P1, 704-48205
Package
1 x Remote Control Box
Fitment Type
Direct Replacement
Model
Side Mount
Color
Show as picture
Package Type
Box
Payment
We accept paypal only
We only ship to verified PayPal addresses. Please make sure your PayPal address is verified and up to date before sending payment. We cannot change any address after checkout has been completed. Please make sure you submit your correct address!
Shipping
1. Items will be shipped within 24 hours after getting your verified payment.
US Storage& UNITED STATES by fast shipping.We offer 24 hours dispatch and estimated delivery time is 3-5 business days.except weekend and other irresistible factors.Please feel free to contact us if you haven't receive the item after the estimated shipping tim
Returns
1.Defective products can be exchanged or returned for full price refund within 30days after you receive the item.
2.Any returning or exchanging item must be in new condition and cannot be tempered.
3. Buyers are responsible to pay the return shipping fee or exchange shipping fee.
4.Please contact us by eBay email first before you return the item Every week we have new items put on sale , if the items you don't need now ,you also can often come to visit my store, maybe one day you can buy the items in our stores which you need.
Contact Us
We treat each buyer with a sincere heart, I believe our sincere service , excellent quality of goods will win your trust and support, you may contact us via message and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)
Every week we have new items put on sale , if the items you don't need now ,you also cam often come to visit my store, maybe one day you can buy the items in our stores which you need.
Hot Item
Heavy Duty Coil Spring Compressor Strut Remover Installer Suspension Tool 2pc
USD 29.99
30 Amp RV Female Plug Replacement Receptacle Plug Male Power Cord Grip Handle
USD 9.89
Rear Step Bumper for 2014-2018 Chevy Silverado GMC Sierra 1500 no Sensor Holes
USD 263.19
10pcs Control Arms Tie Rods Ball Joints Suspension Kit For 1998-2011 Ford Ranger
USD 92.77
For 2001-2006 GMC Yukon 13Pcs Front Upper Control Arms Idler Arm Tie Rods Kit
USD 122.99
Picture
For Yamaha 704-48205-P1 Top Single Binnacle Console Mount Remote Control Box
Product Features
Fast Idle Mode
​
The fast idle button can be used to advance throttle without shifting into gear. With control lever in Neutral, push on fast idle button(cover) to open throttle for starting and warm-up.
Improved Control Handle
​
With control handle in Neutral and fast idle feature not activated, move control handle to Forward gear or Reverse gear position. Continue movement of control handle in same direction to open (advance) throttle.
Safety Lanyard
​
The cord can secure the operation by being attached to operator's clothing, or arm, or leg. Should operators fall down or leave the helm, the cord will pull out the clip, stopping ignition.
Thumb-Operated Trim/Tilt Switch
​
The power trim and tilt switch is attached to the control lever grip and twin cover. Pushing it UP trims up and tilts up the engine and vice versa.​
For Mercury
​
It fits for Mercury/Mariner OB with integral power trim and 1993 and newer Force OB 40hp.
Pistol Grip Remote Control with Finger Tip Lock Release Installation.
1.Route the trim Switch leads from the control handle assembly through the bezel cover and bezel opening.
2.Allow sufficient in the trim switch leads to permit free movement through the full range of the control handle motion.Do not restrain the trim switch leads with cable ties.
3.Install the remote control module to the bezel .Secure the remote control module with three screws .Tighten the screws to the specified torque.
4.Connect the trim switch connector to the trim motor harness connectors.
5.Install the bushing into the module assembly.Apply a small amount of 2-4 C with Teflon to the inside diameter of the bushing.
6.Align the tabs on the bezel cover with the slots on the bezel .Snap the bezel cover in place.
7.Apply Loctite 271 Threadlocker on the threads of the control handle retaining bolt .
8.Install the control handle assembly onto the remote control module .Ensure the control handle is in neutral and in the desired position.
Package Content:
1 x Remote Control Box with Instruction Manual
Product Features
Fast Idle Mode
​
The fast idle button can be used to advance throttle without shifting into gear. With control lever in Neutral, push on fast idle button(cover) to open throttle for starting and warm-up.
Improved Control Handle
​
With control handle in Neutral and fast idle feature not activated, move control handle to Forward gear or Reverse gear position. Continue movement of control handle in same direction to open (advance) throttle.
Safety Lanyard
​
The cord can secure the operation by being attached to operator's clothing, or arm, or leg. Should operators fall down or leave the helm, the cord will pull out the clip, stopping ignition.
Thumb-Operated Trim/Tilt Switch
​
The power trim and tilt switch is attached to the control lever grip and twin cover. Pushing it UP trims up and tilts up the engine and vice versa.​
For Mercury
​
It fits for Mercury/Mariner OB with integral power trim and 1993 and newer Force OB 40hp.
Pistol Grip Remote Control with Finger Tip Lock Release Installation.
1.Route the trim Switch leads from the control handle assembly through the bezel cover and bezel opening.
2.Allow sufficient in the trim switch leads to permit free movement through the full range of the control handle motion.Do not restrain the trim switch leads with cable ties.
3.Install the remote control module to the bezel .Secure the remote control module with three screws .Tighten the screws to the specified torque.
4.Connect the trim switch connector to the trim motor harness connectors.
5.Install the bushing into the module assembly.Apply a small amount of 2-4 C with Teflon to the inside diameter of the bushing.
6.Align the tabs on the bezel cover with the slots on the bezel .Snap the bezel cover in place.
7.Apply Loctite 271 Threadlocker on the threads of the control handle retaining bolt .
8.Install the control handle assembly onto the remote control module .Ensure the control handle is in neutral and in the desired position.
Package Content:
1 x Remote Control Box with Instruction Manual
Product Features
Fast Idle Mode
​
The fast idle button can be used to advance throttle without shifting into gear. With control lever in Neutral, push on fast idle button(cover) to open throttle for starting and warm-up.
Improved Control Handle
​
With control handle in Neutral and fast idle feature not activated, move control handle to Forward gear or Reverse gear position. Continue movement of control handle in same direction to open (advance) throttle.
Safety Lanyard
​
The cord can secure the operation by being attached to operator's clothing, or arm, or leg. Should operators fall down or leave the helm, the cord will pull out the clip, stopping ignition.
Thumb-Operated Trim/Tilt Switch
​
The power trim and tilt switch is attached to the control lever grip and twin cover. Pushing it UP trims up and tilts up the engine and vice versa.​
For Mercury
​
It fits for Mercury/Mariner OB with integral power trim and 1993 and newer Force OB 40hp.
Pistol Grip Remote Control with Finger Tip Lock Release Installation.
1.Route the trim Switch leads from the control handle assembly through the bezel cover and bezel opening.
2.Allow sufficient in the trim switch leads to permit free movement through the full range of the control handle motion.Do not restrain the trim switch leads with cable ties.
3.Install the remote control module to the bezel .Secure the remote control module with three screws .Tighten the screws to the specified torque.
4.Connect the trim switch connector to the trim motor harness connectors.
5.Install the bushing into the module assembly.Apply a small amount of 2-4 C with Teflon to the inside diameter of the bushing.
6.Align the tabs on the bezel cover with the slots on the bezel .Snap the bezel cover in place.
7.Apply Loctite 271 Threadlocker on the threads of the control handle retaining bolt .
8.Install the control handle assembly onto the remote control module .Ensure the control handle is in neutral and in the desired position.
Package Content:
1 x Remote Control Box with Instruction Manual
Product Features
Fast Idle Mode
​
The fast idle button can be used to advance throttle without shifting into gear. With control lever in Neutral, push on fast idle button(cover) to open throttle for starting and warm-up.
Improved Control Handle
​
With control handle in Neutral and fast idle feature not activated, move control handle to Forward gear or Reverse gear position. Continue movement of control handle in same direction to open (advance) throttle.
Safety Lanyard
​
The cord can secure the operation by being attached to operator's clothing, or arm, or leg. Should operators fall down or leave the helm, the cord will pull out the clip, stopping ignition.
Thumb-Operated Trim/Tilt Switch
​
The power trim and tilt switch is attached to the control lever grip and twin cover. Pushing it UP trims up and tilts up the engine and vice versa.​
For Mercury
​
It fits for Mercury/Mariner OB with integral power trim and 1993 and newer Force OB 40hp.
Pistol Grip Remote Control with Finger Tip Lock Release Installation.
1.Route the trim Switch leads from the control handle assembly through the bezel cover and bezel opening.
2.Allow sufficient in the trim switch leads to permit free movement through the full range of the control handle motion.Do not restrain the trim switch leads with cable ties.
3.Install the remote control module to the bezel .Secure the remote control module with three screws .Tighten the screws to the specified torque.
4.Connect the trim switch connector to the trim motor harness connectors.
5.Install the bushing into the module assembly.Apply a small amount of 2-4 C with Teflon to the inside diameter of the bushing.
6.Align the tabs on the bezel cover with the slots on the bezel .Snap the bezel cover in place.
7.Apply Loctite 271 Threadlocker on the threads of the control handle retaining bolt .
8.Install the control handle assembly onto the remote control module .Ensure the control handle is in neutral and in the desired position.
Package Content:
1 x Remote Control Box with Instruction Manual
Payment
Shipping
Returns
Contact Us
We accept paypal only
We only ship to verified PayPal addresses. Please make sure your PayPal address is verified and up to date before sending payment. We cannot change any address after checkout has been completed. Please make sure you submit your correct address!
1. Items will be shipped within 24 hours after getting your verified payment.
US Storage& UNITED STATES by fast shipping.We offer 24 hours dispatch and estimated delivery time is 3-5 business days.except weekend and other irresistible factors.Please feel free to contact us if you haven't receive the item after the estimated shipping tim
1.Defective products can be exchanged or returned for full price refund within 30days after you receive the item.
2.Any returning or exchanging item must be in new condition and cannot be tempered.
3. Buyers are responsible to pay the return shipping fee or exchange shipping fee.
4.Please contact us by eBay email first before you return the item Every week we have new items put on sale , if the items you don't need now ,you also can often come to visit my store, maybe one day you can buy the items in our stores which you need.
We treat each buyer with a sincere heart, I believe our sincere service , excellent quality of goods will win your trust and support, you may contact us via message and we will reply to you within 24 hours from Monday to Saturday.(Excluding local holidays)
Every week we have new items put on sale , if the items you don't need now ,you also cam often come to visit my store, maybe one day you can buy the items in our stores which you need.
All rights reserved.